We’re hard at work on building out our rental fleet and creating a seamless booking experience right here on our site. In the meantime we’re working with an amazing partner, Red Rock Base Camps, who’s renting out custom Escapod teardrop trailers in Moab, Utah.

Sign up for our newsletter and we’ll let you know as soon as we launch our own fleet in Spring/Summer 2018, plus keep you up to date with other big news and Escapod events!

How To Winterize Your Teardrop Trailer

If you have a teardrop trailer with a water system, it’s important to prepare the system for winter. As temps drop below freezing, any water that is left in the plumbing lines or in the pump will freeze and expand, potentially causing damage. This damage will present as leaks come spring.

Below, we’ve outlined the step-by-step process that you’ll need to follow to winterize your teardrop trailer water system.

What You’ll Need:
- RV & Marine specific non-toxic antifreeze (we used Super Tech, found it from Walmart for ~$2/gallon)
- Large Funnel
- Hand-crank for leveling jack (this came with your Escapod)
10’ hose (this came with your Escapod)
- Optional: Driver with 13/16 bit (to use instead of the hand-crank)

Most of these supplies come with your Escapod. Purchasing a funnel and the antifreeze should be less than $10 total.
1. Open the output flow (left side) and run the pump until the water flow decreases to a sputter.
2. Extend the leveling jack on the opposite the water output to raise the trailer, thus allowing more water flow out of the tank.
3. Keep the valve open and pump on and lower the leveling jack back to its original position. At this point no water should be exiting the output nozzle.
4. Close the output valve and turn off the pump.
1. Open the input valve (right side) to the water tank.
2. Secure one end of the hose to the input, and the other end to the funnel.
3. Slowly pour the antifreeze into the funnel and keep it elevated to gravity-feed it into the tank.
4. Remove the hose and close the input valve (right side).
5. Open the output valve (left side) and turn on the pump until the pink liquid begins to flow out. (If it doesn't flow, just lift up the opposite side of the trailer again with the leveling jacks).
At this point the antifreeze has filled the pump and lines, and is safe to leave sitting for the duration of the freezing months!

If you're more of a visual learner, check out our video walk-through on YouTube!
Screen Shot 2019 10 11 At 2 33 49 Pm
A few other things to note: If you have our water heater installed as well, you’ll want to follow a few easy steps to winterize.

Water Heater Winterization:
1. Disconnect the water inlet and shower hose from the bottom of the appliance.
2. Loosen the drain valve from the bottom of the water heater.

Ensure this process is completed. Warranty is void if damage is caused by freezing water.
Screen Shot 2019 10 11 At 5 25 47 Pm
Also, come spring, you’ll need to sanitize the system before use. Follow these steps to ensure your water system is ready to go! As we get our rental fleet up-and-running in the spring, we’ll repost this with a video tutorial.

De-winterizing and Sanitizing for Spring:
1. Follow the 'Prep' process (outlined above) to drain as much of the antifreeze out of the tank as possible.
2. Hook a water source to the input valve (right side) and fill the tank with fresh water.
Close the input valve (right side), open the output valve (left side) and empty the entire tank.
3. Gravity feed 1/4 cup of household bleach into the tank using a funnel.
4. Remove funnel & reconnect to your water source.
5. Fill the remaining tank with fresh water.
6. Let bleach & water mixture sit for 12 hours.
7. Finally, drain & flush the tank (Repeat as needed until the smell of bleach is no longer detectable in the water flow).
Please do not hesitate to reach out with any questions (or suggestions)! This is the best method we've found through research and experience, but if you have a better way we'd love to hear about it.

Stay warm!

The Escapod Team